One, four hours before class drinkers, bad state of mind and emotional range are not allowed to arrange for employment, is strictly prohibited classes drink, sleep.
two posts before the wearing of a good labor protection products, shall not wear slippers and high heels to work, women long hair into the cap shall within.
three centrifuges centrifuges must be familiar with the performance of drivers and construction principles, knowledge of the rules, according to good standards of maintenance of centrifuges. The certification training and examinations and obtain certificates before.
four, not with wet hands open and close electrical switches, and should be hand operation. Should be no load start, not overloaded.
five centrifuge machines feeding should be kept uniform. Must take effective measures to remove the debris into the compound, in particular iron, so as to avoid damage to the stainless steel sieve basket.
six, regular checks of centrifuge machine lubrication system to maintain circuit patency. Oil shall not be less than the technical requirements, and prevent oil leakage.
seven, pay close attention to the operation of centrifuge operation is smooth. Strong vibration appears to timely check processing.
eight, in the operation process, the non-iron, wood and other debris into the centrifuges.
IX, no major emergencies, not allowed to stop the centrifuge with a load.
ten and found that safety problems should be timely, accurate reporting,UGGs, not hiding and secretly handled.
13, magnetic separator safety regulations
one, where class four hours before drinking, bad state of mind or emotional range, shall not arrange for employment, alcohol is prohibited to sleep in class.
two posts before the wearing of a good labor protection products, not wear high-heeled shoes and slippers to work, women long hair into the cap shall within.
three, without any safety training, and do not participate in classes before the Council who shall cause induction.
Fourth, non-opening and closing electrical switches with wet hands, press the switch should be hand operation.
five, check the rotating parts of the fault should be avoided, and strictly enforce the stop transmission system.
six, inspection, treatment failures should be avoided moving parts, and strictly enforce the stop transmission system.
eight, equipment operation, and forbids any person or other object by hand cleaning or maintenance equipment, parts of the operation.
nine, repair or cleaning equipment should be clean power, and strict implementation of stopping transmission system.
ten and found that safety problems should be timely, accurate reporting, not hiding and secretly handled.
14, vacuum safety regulations
one, where the first four hours of drinking, bad state of mind and emotional range are not allowed to arrange for employment, is strictly prohibited classes drink, sleep.
two posts before the wearing of a good labor protection products, not wear high-heeled shoes or slippers to work, women long hair into the cap shall within.
Third, without safety training and those who do not participate in class will not be arranged prior to appointment.
IV, cleaning crew to place the tools and debris, to prevent the pump running in the accident.
five, not wet hands open and close electrical switches. Check the device away from rotating parts should be found that safety problems should be timely and accurate reporting to the control room, without concealment or private treatment.
six steering motors and should ensure that the provisions of the steering pump the same direction, not the reverse rotation, release or otherwise cause damage to other parts of the impeller.
seven, should not oil-free drive!
eight, opening and closing the valve can not be too dead, leave some deduction should be appropriate.
nine, always check the mechanical functioning of ministries, temperature, sound, and is normal.
ten, is strictly prohibited under the pump for taking the time to run, because the pump is not only in taking the time to run under severe vibration, but also affect the pump life, we must pay special attention.
XI pump allowed to enter the metal objects and more than allowed by the bulk solids pump, and allowed to enter the rubber, cotton, silk, plastic sheeting and the like flexible material, so as not to undermine the flow components and plug the impeller so that the pump does not work.
second, running the course of the abnormal phenomenon is found, treatment should be provided electricity, troubleshooting, can only continue to operate.
thirteen, always check the pump and related equipment, should strictly enforce stopping transmission system.
fourth, equipment operation, and forbids any person or other object by hand cleaning or maintenance equipment, parts of the operation.
fifth, repair or cleaning equipment should be clean power, and strict implementation of stopping transmission system.
XVI safety problems found should be timely and accurate reporting, not to conceal or private treatment.
15, high-pressure pump safety regulations
one, where class four hours before drinking, poor mental state and emotional range are not allowed to arrange for employment, is strictly prohibited classes drink, sleep.
two posts before the wearing of a good labor protection products, not wear high-heeled shoes or slippers to work, women long hair into the cap shall within.
Third, without safety training and those who do not participate in class will not be arranged prior to appointment.
IV, cleaning crew to place the tools and debris, to prevent the pump running in the accident. KV class high-pressure water pump switch operation, the staff must wear insulated gloves and shoes to wear electrical insulation. Special attention.
ten, see the water level when the ladder is a good solid check, effort should be concentrated.
XI before the first check to open the pump: voltage does not exceed the rated voltage of +10 ~ -8%; lubrication clean, oil appropriate.
second, the pump allowed to enter the metal objects and more than allowed by the bulk solids pump, and allowed to enter the gum, cotton, silk, plastic sheeting and the like flexible material, so as not to undermine the flow components and plug the impeller so that the pump does not work.
XIII, dealing with failure, and scheduling contact must be good, personal maintenance outage, power outages linked to licensing, and other personnel is prohibited to use equipment switch.
fourth, equipment operation are not allowed to doze off, not allowed to slapstick, running in the bush should always check the motor temperature does not exceed 40 ℃, pump bearing temperature does not exceed 75 ℃, the oil ring rotation flexibility, motor temperature l do not exceed nameplate ingot, sounds normal.
fifth, equipment operation, and forbids any person or other object by hand cleaning or maintenance equipment, parts of the operation.
sixteen, repair or cleaning equipment should be clean power, and strict implementation of stopping transmission system.
seventh, running the course of the abnormal phenomenon is found, treatment should be provided electricity, troubleshooting, can only continue to operate.
eighteen, found safety problems should be reported promptly and accurately, without concealment, or unauthorized treatment.
16, centrifugal pump safety regulations
one, where class four hours before drinking, poor mental state and emotional range are not allowed to arrange for employment, is strictly prohibited classes drink, sleep.
two posts before the wearing of a good labor protection products, not wear high-heeled shoes or slippers to work, women long hair into the cap shall within.
Third, without safety training and those who do not participate in class will not be arranged prior to appointment.
IV, cleaning crew to place the tools and debris, to prevent the pump running in the accident.
five, not wet hands open and close electrical switches. Check the device away from rotating parts should be found that safety problems should be timely and accurate reporting to the control room, without concealment, or unauthorized treatment.
six steering motors and should ensure that the provisions of the steering pump the same direction, not the reverse rotation, release or otherwise cause damage to other parts of the impeller.
seven, should not oil-free drive! Opening and closing the valve can not be too dead, leave some deduction should be appropriate.
eight, open, parking should be to contact the control room and related positions completely.
IX, no material is strictly prohibited under the pump to run, because the pump is not only in taking the time to run under severe vibration, but also affect the pump life, we must pay special attention. Death may not close the gate long-running case. Operation, the suction pipe submerged depth of not less than 0.5 meters.
ten, see the water level when the ladder is a good solid check, effort should be concentrated.
XI before the first check to open the pump: voltage does not exceed the rated voltage of +10 ~ -8%; lubrication clean, oil appropriate.
second, the pump allowed to enter the metal objects and more than allowed by the bulk solids pump, and allowed to enter the rubber, cotton, silk, plastic sheeting and the like flexible material, so as not to undermine the flow components and plug the impeller so that the pump does not work.
XIII, dealing with failure, and scheduling contact must be good, personal maintenance outage, power outages linked to licensing, and other personnel is prohibited to use equipment switch.
fourth, equipment operation are not allowed to doze off, not allowed to slapstick, running in the bush should always check the motor temperature does not exceed 40 ℃, pump bearing temperature does not exceed 75 ℃, the oil ring rotation flexibility, motor temperature l do not exceed nameplate ingot, sounds normal.
fifth, equipment operation, and forbids any person or other object by hand cleaning or maintenance equipment,UGG bailey button, parts of the operation.
sixteen, repair or cleaning equipment should be clean power, and strict implementation of stopping transmission system.
seventh, running the course of the abnormal phenomenon is found, treatment should be provided electricity, troubleshooting, can only continue to operate.
eighteen, found safety problems should be reported promptly and accurately, without concealment, or unauthorized treatment.
17, slurry pump safety regulations
one, where the drink is not fully awake, bad state of mind and emotional range are not allowed to arrange for employment, is strictly prohibited classes drink, sleep.
two posts before the wearing of a good labor protection products, not wear high-heeled shoes or slippers to work, women long hair into the cap shall within.
three,UGG shoes, who have not traveled to participate in safety training and will not participate in classes before the people, shall not cause induction.
four switches can not switch with wet hands, press the switch should be hand operation.
be regularly check the mechanical operation of the components, temperature, sound and the instrument instructions, etc. is normal, to avoid moving parts should be checked and found that safety problems should be timely and accurate reporting to the control room, without concealment or unauthorized treatment.
six, not to run in the absence of material circumstances, shall not die in the gate closed long-running case. Operation, a small suction pipe submerged depth of not more than 0.5 meters.
seven, treatment failure, and scheduling contact must be good, repair power when someone hanging power card.
18, the media pump safety regulations
one, where the drink is not fully awake, bad state of mind and emotional range are not allowed to arrange for employment, is strictly prohibited classes drink, sleep.
two posts before the wearing of a good labor protection products, not wear high-heeled shoes or slippers to work, have to drive into the hair inside the cap.
Third, without safety training and those who do not participate in class will not be arranged prior to appointment.
four, not wet hands switch switch. Check the device away from rotating parts should be found that safety problems should be timely and accurate reporting to the control room, without concealment, or unauthorized treatment.
V. sweeping workplace shall not wash with water electrical equipment, cables, lighting, signal transmission lines and equipment components. Bearing cooling water shall not use water washout.
six, check the cyclone and other related equipment, should strictly enforce stopping transmission system.
19, piston air compressor safety regulations
one, where the drink is not fully awake, bad state of mind or emotional range, shall not arrange for employment, alcohol is prohibited to sleep in class.
two posts before the wearing of a good labor protection products, not wear high-heeled shoes and slippers to work, women long hair into the cap shall within.
three, without any safety training, and do not participate in classes before the Council who shall cause induction.
Fourth, non-opening and closing switches with wet hands, press the switch should be hand operation.
five, must be carefully checked before driving: crankshaft bolt tile, the piston, crosshead nut is loose; primer within the crankcase oil, oil is accurate; belt tension is appropriate,Bailey UGG boots, with or without rupture, the motor bolt is loose; all representatives are in good condition, safety devices: such as guard, cover bars, water protection, high and low pressure safety valve, is intact; voltage at rated voltage (+10 ~ -8%) range.
six, bearing temperatures never exceed 75 ℃, sliding bearings should never exceed 65 ℃, oil pressure gauge pressure 1 ~ 25Kg/Cm2, high-pressure cylinder pressure does not exceed 8 Kg/Cm2.
seven, coolers, cylinders and other use and management of pressure vessels shall be the State Administration of Safety Supervision of Labor Regulations Chapter V,
eight regular maintenance in accordance with the provisions of the air compressor with 5% aqueous solution of caustic soda carefully remove valves, valve chamber and the gas chamber, cooling chamber, gas tank and exhaust pipe of the coke. After washing with water to rinse off base, and blowing with compressed air clean. So as to avoid excessive carbon deposition, the high temperature caused by fire, carbon monoxide and carbon dioxide generated Dali, and cause the compressor explosion.
nine, the timely removal of the exhaust channel of the soot deposition, in order to avoid explosion. .
ten, always check the air compressor part of the grounding of electrical equipment is properly completed.
XI, inspection, treatment failures should be avoided moving parts, and strictly enforce the stop transmission system. And are prohibited in the equipment operation, wipe the moving parts.
second check of the instrumentation and protection equipment (off oil, water, over-temperature, over-pressure) should be carefully.
thirteen, safety equipment, fire fighting equipment intact.
fourteen, found safety problems should be timely and accurate reporting, not to conceal or private treatment.
20, screw air compressor safety regulations
one, where the drink is not fully awake, bad state of mind or emotional range, shall not arrange for employment, alcohol is prohibited to sleep in class.
two posts before the wearing of a good labor protection products, not wear high-heeled shoes and slippers to work, women long hair into the cap shall within.
three, without any safety training, and do not participate in classes before the Council who shall cause induction.
Fourth, non-opening and closing switches with wet hands, press the switch should be hand operation.
five, must be carefully checked before driving: pressure gauge is intact, the pressure controller action is accurate and flexible, the crankcase oil inside the grease clean oil in the oil window should be 1 / 2, V-belt tension is appropriate, with or without rupture, the motor is loose anchor bolts, safety protection device: shield, the safety valve is intact. Within the regular class condensate tank emissions.
six gauge pressure of not more than 1.5MPa..
seven regular maintenance in accordance with the provisions of the air compressor with 5% aqueous solution of caustic soda carefully remove valves, valve chamber and the gas chamber, cooling chamber, gas tank and exhaust pipe of the coke.
eight, the timely removal of the exhaust channel of the soot deposition, in order to avoid explosion. .
nine, inspection, treatment failures should be avoided moving parts, and strictly enforce the stop transmission system. And are prohibited in the equipment operation, wipe the moving parts.
ten, check the meter and protective equipment should be carefully.
November, found that safety problems should be timely and accurate reporting, not to conceal or private treatment.
21, to clarify the pump
one, where the drink is not fully awake, bad state of mind and emotional range are not allowed to arrange for employment, is strictly prohibited classes drink, sleep.
two posts before the wearing of a good labor protection products, not wear high-heeled shoes or slippers to work, women long hair into the cap shall within.
three, who have not traveled to participate in safety training and will not participate in classes before the people, shall not cause induction.
four switches can not switch with wet hands, press the switch should be hand operation.
be regularly check the mechanical operation of the components, temperature, sound and the instrument instructions, etc. is normal, to avoid moving parts should be checked and found that safety problems should be timely and accurate reporting to the control room, without concealment or unauthorized treatment.
six, not to run in the absence of material circumstances, shall not die in the gate closed long-running case. Operation, a small suction pipe submerged depth of not more than 0.5 meters.
seven, treatment failure, and scheduling contact must be good, repair power when someone hanging power card.
22, effective concentration for the safety rules
one, where class four hours before drinking, poor mental state and emotional range are not allowed to arrange for employment, is strictly prohibited classes drink, sleep.
two posts before the wearing of a good labor protection products, not wear high-heeled shoes or slippers to work, women long hair into the cap shall within.
III concentrator concentrator drivers must be familiar with the performance and principles, knowledge of the rules, according to the standard maintenance concentrator, understand the production process. Without safety training and do not participate in those classes will not be arranged prior to induction.
four, not wet hands open and close electrical switches. Check the device away from rotating parts should be found that safety problems should be timely and accurate reporting to the control room, without concealment, or unauthorized treatment.
five different parts of concentrated machine screws, must be solid, safe and complete. If the interrupt pin in operation, should be immediately reported, parking repairs.
six, to prevent debris falling into the pool and all other tools, such as the treatment that should be promptly reported.
seven concentrator must be installed throughout the corridor railings, the floor should be spent spinning plate, and install it securely.
eight, non-stored in the thickener to go on the bridge debris, to prevent tools and other debris falling into the pool.
nine, and forbids any person around the concentrator up, sit, stand or work.
ten, equipment operation, and forbids any person or other object by hand cleaning or maintenance equipment, parts of the operation.
November, when parking is prohibited thickener feed. Thickener happened during operation overload shutdown signal will be sent sirens and lights, and you should immediately stop feeding, try to drain as soon as the end of stream.
second, treatment failure, maintenance or cleaning equipment should be power handling, and strict implementation of stopping transmission system.
23, the end of current safety regulations pump
one, where the drink is not fully awake, bad state of mind and emotional range are not allowed to arrange for employment, is strictly prohibited classes drink, sleep.
two posts before the wearing of a good labor protection products, not wear high-heeled shoes or slippers to work, with long hair should be within the disc into the cap.
three, who have not traveled to participate in safety training and will not participate in classes before the people, shall not cause induction.
four switches can not switch with wet hands, press the switch should be hand operation.
be regularly check the mechanical operation of the components, temperature, sound and the instrument instructions, etc. is normal, to avoid moving parts should be checked and found that safety problems should be timely and accurate reporting to the control room, without concealment or unauthorized treatment.
six, sweeping workplace shall not wash with water electrical equipment, cables, lighting, signal transmission lines and equipment components. Bearing cooling water may not use the water washout.
VII shall not be run in the absence of material conditions; not gate closed in case of death of long-term operation; operation, suction tube submerged depth of not less than 0.5 meters.
eight, treatment failure, must control room, power distribution room to contact a good, repair power when someone hanging power card.
24, belt filter press safety rules
1, operation of the driver must be familiar with the working principle of belt filter press, technical characteristics, belt filter press process to understand the system and related electrical equipment, basic working principle.
2, operation of the driver must be trained, proficient in belt filter press of the
3, where four hours before class drinkers, bad state of mind and emotional range are not allowed to arrange for employment, alcohol is strictly prohibited classes, sleep, and off-site.
4, dressed before induction of labor protection products, shall not wear slippers and high heels to work, women long hair into the cap shall within.
5, before driving the main motor speed switch to zero, is strictly prohibited governor switch is not zero to start the main motor, belt filter press the filter must be specified with the direction (forward direction ) run.
6, the boot device should be empty, non-overload operation, the handling capacity (into the feeding amount), cake thickness, filter belt tension and speed are no more than the specified value.
7, with the press of a material, cloth should be kept uniform and stable, feed impurity must take effective measures, non-coarse, bulk materials and other debris into the filter press filter belt .
8, each device on the system equipment, instruments must be sensitive and reliable to indicate normal operation of equipment in various directions parameters (such as air pressure, water pressure, with pressure, voltage, current, etc.) shall not exceed the specified value .
9, running with a serious deviation in the filter, filter with a tear, filter transfer and other machines with no serious faults air equipment must deal with an emergency stop.
10, with the necessary positions on the fire-fighting facilities, fire facilities at any time to keep all reliable.
11, strictly in accordance with operating procedures in order to operate the equipment, not with wet hands open and close electrical switches, and should be hand operation, non-illegal operations, refused to illegal command, abnormal and safety problems, timely reporting and timely treatment.
12, equipment operation logs, maintenance records must be completed and recorded clearly, keeping complete.
13, flocculant addition system should take anti-slip. Feeding is stopped, and equipment should be around the filter with a clean.
25, purification station safety regulations
one purification station drivers must go through security training, employees eligible to obtain permits, and certificates.
Second, all within four hours before class drinkers, bad state of mind and emotional range are not allowed to arrange for employment, alcohol is strictly prohibited classes, sleeping, dry matter not related to work, off.
three posts well before the operator must wear labor protection products, wear a helmet. Long hair should be within the disc into the cap. Forbidden to wear skirts, shorts, wearing a scarf, wear high heels, wearing slippers and bare feet in field operations.
four sewage pumping stations within the purification station pool dosing dosing must be two people at work, cooperate, according to chapter operations.
five to purify the sewage pumping station, the inspection dosing tank, motors, pumps and other operating conditions must be inspected at the same time 2.
six, clean diatomite bags must be clean to get a designated area outside the duty room.
July, when the sewage purification tower needs to be 2 persons is to operate.
VIII, visited the tower on the purification of water quality must be above 2 the same is prohibited in the purification tower chat, slapstick.
September, 1400,1660 observed runoff, water supply and the situation must be 2 persons into an observation.
ten, purification stations for all staff, is strictly prohibited on the walk in the sewage pool partitions.
November, when a person needs to leave the duty room must be on duty with another greeting.
XI on non-staff members are not allowed to clean the tower and clear pool.
No comments:
Post a Comment